Loading...

ABOUTAbout the factory
EQUIPMENTEquipment introduction
FUNCTIONSFunctions of a factory
DEPARTMENTDepartment introduction

JUKI official site

JP
EN
CN

Equipment introduction

JUKI official site

JP
EN
CN

HOME
Equipment introduction

Processing equipment line-ups

Processing range [1000 mm x 900 mm x 925 mm]
This horizontal machining center is equipped with a table of 630 x 630 mm pallet changers.

Processing range [720 mm x 680 mm x 780 mm]
This horizontal machining center is equipped with a table of 500 x 500 mm pallet changers.

Processing range [300 mm x 300 mm x 450 mm]
This machine enables 5-axis processing by adding lathe functions and an inclined axis to the conventional functions of a machining center. The machine is also capable of substantially reducing processing time.

Processing range [1600 mm x 650 mm x 660 mm]
This machining center with a horizontal processing range of 1600 mm is suitable for processing large materials.

Processing range [700 mm x 300 mm x 300 mm]
This machine properly handles numerically controlled milling processes according to the software instructions provided. This particular model has seen long years of service but still works perfectly for long hours.

Processing range [400 mm x 300 mm x 150 mm]
This machine discharges electricity to the parts being processed in a machining fluid for precision processing. No problems occur even when the wiring is disconnected by the automatic wire connection function. Unattended operation of the machine is possible.

Processing range [2500 mm x 1200 mm x 300 mm]
This machine is equipped with a two-dimensional carbon dioxide laser. Customers use it to process steel with board thicknesses ranging from 0.1 to 15 mm.

Processing range [260 mm x 590 mm]
This machine is used both as a conventional milling machine and NC milling machine. The machine can also perform a wide variety of processing maneuvers with a single chuck.

Processing range [1300 mm x 800 mm x 100 mm]
The wide processing range of this machine allows it to handle small to large materials. The rich line-up of grinding stones used with the machine enable the handling of processing-resistant materials. The machine processes parts with a flatness accuracy as high as 0.005/500.

Maximum processing size [700 mm x 300 mm x 20 mm]
The furnace penetrates carbon into the surface of low carbon steel and then quench it to produce high carbon steel. The surface is hard, with excellent wear resistance, while the interior remains extremely tough even in the soft state. The processing temperature ranges from 790 to 910 ℃.

Maximum processing size [200 mm x 100 mm x 10mm]
The device hardens the surface of the parts being processed by charging an N-Plus ion generated by the discharged nitrogen gas on the surface and diffusing an activated nitrogen element. The processing temperature ranges from 500 to 570 ℃.

Maximum processing size [300 mm x 300 mm x 10 mm]
After the furnace heats a salt bath (salt bus: salt-bath furnace) to fuse the salt, the parts being processed are placed into the bath and either heated or cooled. The processing temperature ranges from 830 to 850 ℃.

Maximum processing size [300 mm x 300 mm x 100 mm]
The tank creates one or more metallic compounds and changes coloring of the surface by inducing chemical changes in the surfaces of the metals. The tank also changes the colors of metal surfaces and improves corrosion resistance.

Maximum processing size [300 mm x 300 mm x 100 mm]
This tank creates metallic antirust films and surfaces for painting by forming oxide films and thin films of inorganic salt on metal surfaces through chemical reactions with solutions.　The tank is used for wear prevention of a sliding portion at early stages of use, corrosion protection, curable coating on the metal surface, and coloring of the surface.

Maximum processing size [300 mm x 80 mm x 25 mm]
This tank reinforces the corrosion resistance and wear resistance of aluminum materials.　This reinforcement makes up for the demerits of aluminum material and reduces the weight of the material compared with iron.

JUKI Corporation Ohtawara Plant

1863, Kita-Kanemaru, Ohtawara-shi, Tochigi, 324-0011

TEL. +81-287-23-5111 Google Map

JUKI Corporation
Privacy Policy
Site Map

© JUKI CORPORATION. All rights reserved.